AbstractAbout AuthorsReferences
A criterion, indicators and results of evaluation of technical and economic efficiency of 3D printing technology application in the housing and construction sphere are considered. As a criterion of efficiency, the minimum cost per 1 m2 of total area of the residential object under construction is used. In this case, the indicators of direct costs and labor intensity of construction of the building are calculated. The assessment of technical and economic efficiency of 3D-additive building technology was carried out on the example of a two-storey cottage of mass building. Four variants of its construction differing in the materials and technologies used were analyzed. As a result of calculations it is received that at the set conditions and in the case of application of original mixes developed in VSTU, the variant on the basis of 3D-printing is the most effective. In the case of using mixtures purchased at relatively high market prices, this technology is comparable to the prefabricated technology using gas silicate small blocks.
I.I. AKULOVA, Doctor of Sciences (Economy), (This email address is being protected from spambots. You need JavaScript enabled to view it.)
G.S. SLAVCHEVA, Doctor of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
T.V. MAKAROVA, Candidate of Sciences (Engineering), (This email address is being protected from spambots. You need JavaScript enabled to view it.)
G.S. SLAVCHEVA, Doctor of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it.)
T.V. MAKAROVA, Candidate of Sciences (Engineering), (This email address is being protected from spambots. You need JavaScript enabled to view it.)
Voronezh State Technical University (84, 20-letiya Oktyabrya Street, 394006, Voronezh, Russian Federation)
1. Чернышов Е.М., Акулова И.И., Кухтин Ю.А. Ресурсосберегающие архитектурно-строительные системы для жилых зданий (Воронежский опыт) // Градостроительство. № 5 (15). 2011. С. 70–73.
1. Chernyshov E.M., Akulova I.I., Kukhtin Yu.A. Resource-saving architectural and construction systems for residential buildings (Voronezh experience). Gradostroitel’stvo. No 5 (15). 2011, pp. 70–73. (In Russian).
2. Акулова И.И. Прогнозирование динамики и структуры жилищного строительства в регионе. Воронеж.: ВГАСУ, 2007. 132 с.
2. Akulova I.I. Prognozirovanie dinamiki i struktury zhilishchnogo stroi-tel’stva v regione [Forecasting the dynamics and structure of housing in the region]. Voronezh: VGASU. 2007. 132 p.
3. Грахов В.П., Мохначев С.А., Бороздов О.В. Влияние развития 3D-технологий на экономику строительства // Фундаментальные исследования. 2014. № 11 (часть 12). С. 273–276.
3. Grahov V.P., Mohnachev S.A., Borozdov O.V. The impact of the 3D technology development on the construction economy. Fundamental’nye issledovanija. 2014. No. 11 (Part 12), pp. 273–276. (In Russian)
4. Bos F., Wolfs R., Ahmed Z et al. Additive manu-facturing of concrete in construction: potentials and challenges of 3D concrete printing. Virtual and Physical Prototyping. 2016. Vol. 11. No. 3, pp. 209–225.
5. Hage I., Golonka A., Putanowicz R. 3D printing of buildings and building components as the future of sustainable construction? Procedia Engineering. 2016. Vol. 151, pp. 292–299.
6. Krimi I., Lafhaj Z., Ducoulombier L. Prospective study on the integration of additive manufacturing to building industry – Case of a French construction company. Additive Manufacturing. 2017. Vol. 16, pp. 107–114.
7. Tay Y. W. D. et al. 3D printing trends in building and construction industry: a review. Virtual and Physical Prototyping. 2017. No. 12 (3), pp. 1–16.
8. Wu P., Wang J., Wang X. A critical review of the use of 3-D printing in the construction industry. Automation in Construction. 2016. No. 60, pp. 21–31.
9. Славчева Г.С., Артамонова О.В. Реологическое поведение дисперсных систем для строительной 3d-печати: проблема управления и возможности арсенала «нано» // Нанотехнологии в строительстве: научный интернет-журнал. 2018. Т. 10. № 3. С. 107–122. DOI: 10.15828/2075-8545-2018-10-3-107-122
9. Slavcheva G.S., Artamonova O.V. The rheological behavior of disperse systems for 3D printing in construction: the problem of control and possibility of «nano» tools application. Internet-journal «Nanotechnologii v stroitel’stve». 2018. Vol. 10. No. 3, pp. 107–122. (In Russian). DOI: 10.15828/2075-8545-2018-10-3-107-122
10. Славчева Г.С., Макарова Т.В. Пенобетоны для теплоизоляционных слоев наружных стен, возводимых методом 3D-печати // Строительные материалы. 2018. № 10. С. 30–35. DOI: https://doi.org/10.31659/0585-430X-2018-764-10-30-35
10. Slavcheva G.S., Makarova T.V. Foam concretes for heat insulation layers of external walls constructed by the method of 3D printing. Stroitel’nye Materialy [Construction Materials]. 2018. No. 10, pp. 30–35. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2018-764-10-30-35
11. Акулова И.И. Исследование и учет потребительских предпочтений на рынке жилой недвижимости как основа формирования эффективной градостроительной политики // Жилищное строительство. 2017. № 4. С. 3–6.
11. Akulova I.I. Research and accounting of consumer preferences in the residential real estate market as a basis for the formation of an effective urban development policy. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2017. No. 4, pp. 3–6. (In Russian).
12. Акулова И.И., Славчева Г.С. Методические подходы к нормированию затрат на эксплуатацию машин и механизмов для строительного 3D-принтера // Жилищное строительство. 2019. № 11. С. 26–30. DOI: https://doi.org/10.31659/0044-4472-2019-11-26-30
12. Akulova I.I., Slavcheva G.S. Methodological approaches to rationing the cost of operation of machines and mechanisms for 3d-construction printer. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2019. No. 11, pp. 26–30. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2019-11-26-30
1. Chernyshov E.M., Akulova I.I., Kukhtin Yu.A. Resource-saving architectural and construction systems for residential buildings (Voronezh experience). Gradostroitel’stvo. No 5 (15). 2011, pp. 70–73. (In Russian).
2. Акулова И.И. Прогнозирование динамики и структуры жилищного строительства в регионе. Воронеж.: ВГАСУ, 2007. 132 с.
2. Akulova I.I. Prognozirovanie dinamiki i struktury zhilishchnogo stroi-tel’stva v regione [Forecasting the dynamics and structure of housing in the region]. Voronezh: VGASU. 2007. 132 p.
3. Грахов В.П., Мохначев С.А., Бороздов О.В. Влияние развития 3D-технологий на экономику строительства // Фундаментальные исследования. 2014. № 11 (часть 12). С. 273–276.
3. Grahov V.P., Mohnachev S.A., Borozdov O.V. The impact of the 3D technology development on the construction economy. Fundamental’nye issledovanija. 2014. No. 11 (Part 12), pp. 273–276. (In Russian)
4. Bos F., Wolfs R., Ahmed Z et al. Additive manu-facturing of concrete in construction: potentials and challenges of 3D concrete printing. Virtual and Physical Prototyping. 2016. Vol. 11. No. 3, pp. 209–225.
5. Hage I., Golonka A., Putanowicz R. 3D printing of buildings and building components as the future of sustainable construction? Procedia Engineering. 2016. Vol. 151, pp. 292–299.
6. Krimi I., Lafhaj Z., Ducoulombier L. Prospective study on the integration of additive manufacturing to building industry – Case of a French construction company. Additive Manufacturing. 2017. Vol. 16, pp. 107–114.
7. Tay Y. W. D. et al. 3D printing trends in building and construction industry: a review. Virtual and Physical Prototyping. 2017. No. 12 (3), pp. 1–16.
8. Wu P., Wang J., Wang X. A critical review of the use of 3-D printing in the construction industry. Automation in Construction. 2016. No. 60, pp. 21–31.
9. Славчева Г.С., Артамонова О.В. Реологическое поведение дисперсных систем для строительной 3d-печати: проблема управления и возможности арсенала «нано» // Нанотехнологии в строительстве: научный интернет-журнал. 2018. Т. 10. № 3. С. 107–122. DOI: 10.15828/2075-8545-2018-10-3-107-122
9. Slavcheva G.S., Artamonova O.V. The rheological behavior of disperse systems for 3D printing in construction: the problem of control and possibility of «nano» tools application. Internet-journal «Nanotechnologii v stroitel’stve». 2018. Vol. 10. No. 3, pp. 107–122. (In Russian). DOI: 10.15828/2075-8545-2018-10-3-107-122
10. Славчева Г.С., Макарова Т.В. Пенобетоны для теплоизоляционных слоев наружных стен, возводимых методом 3D-печати // Строительные материалы. 2018. № 10. С. 30–35. DOI: https://doi.org/10.31659/0585-430X-2018-764-10-30-35
10. Slavcheva G.S., Makarova T.V. Foam concretes for heat insulation layers of external walls constructed by the method of 3D printing. Stroitel’nye Materialy [Construction Materials]. 2018. No. 10, pp. 30–35. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2018-764-10-30-35
11. Акулова И.И. Исследование и учет потребительских предпочтений на рынке жилой недвижимости как основа формирования эффективной градостроительной политики // Жилищное строительство. 2017. № 4. С. 3–6.
11. Akulova I.I. Research and accounting of consumer preferences in the residential real estate market as a basis for the formation of an effective urban development policy. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2017. No. 4, pp. 3–6. (In Russian).
12. Акулова И.И., Славчева Г.С. Методические подходы к нормированию затрат на эксплуатацию машин и механизмов для строительного 3D-принтера // Жилищное строительство. 2019. № 11. С. 26–30. DOI: https://doi.org/10.31659/0044-4472-2019-11-26-30
12. Akulova I.I., Slavcheva G.S. Methodological approaches to rationing the cost of operation of machines and mechanisms for 3d-construction printer. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2019. No. 11, pp. 26–30. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2019-11-26-30
For citation: Akulova I.I., Slavcheva G.S., Makarova T.V. Technical and economic estimate of efficiency of using 3D printing in housing construction. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2019. No. 12, pp. 52–56. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2019-12-52-56